SS155 User Manual

Remarks: (1)Pairing mode will timeout automatically after pairing is completed. WC180-SS Receiver & Transmitter Installation (2)Pairing mode will last for 5 seconds only.

• Important: Test the range before mounting the push button (or other
• compatible sensor). The sensor will be referred to as a
• Two or more transmitters pairing:
• "transmitter" in this document. The options below are for a push
• Only one transmitter can be programmed at a time. For additional
• button. If using a different transmitter type, consult that manual.
• transmitters, please follow the pairing steps (1)-(3) once again to pair

the transmitters one by one. Transmitter Installation Method 1: Double-sided adhesive tape. (Easiest install method) It is common practice to choose a different ringtone for each 1.After ensuring the right mounting position, please clean the flat area transmitter so you can distinguish which transmitter is being where you intend to install transmitter.

• triggered. 2.Tear off one side of the double-sided adhesive tape and stick it to
• the underside of transmitter; tear off the other side and place the
• Factory Reset: transmitter on the wall. Hold in place for 10 seconds.
• Hold the Music Change button for approximately 5 seconds. You

will hear a short ‘Ding Dong’ ringtone and a quick flash of the LED Transmitter Installation Method 2: Screw/Anchors strobe light. This indicates the receiver has reset to factory settings Please prepare an electric drill, Phillips screwdriver and slotted which is no transmitter paired and the receiver set to the "Ding- screwdriver before installation.

• Dong" sound. 1.Use the small screwdriver to separate the top half of the case
• from the lower half of the cases.
• Changing the Ringtone: 2.Using the back half of the case as a template, make two marks

Refer to Step 3 in the "Quick Start" section of this manual. on the wall where the pre-drilled holes are located.

• 3.Drill two holes on the marked places, then insert the wall
• anchors (if needed).
• 4.Use the supplied screws to secure the back half of the push

button to the wall. 5.Snap top half of push button cover to lower half. 4 5

• What You Should Know Before Using
• 1.The transmitter (push button) supplied with this kit comes paired with
• the receiver from the factory, set to default ringtone “Ding-Dong”. If you
• are only using the push button included with this kit and are okay with
• the "Ding-Dong" ringtone, then there is no programming/pairing
• required.
• 2.IF NOT, please refer to the “Quick Start” section to pair the
• transmitter with the receiver and set your favorite ringtone(s).
• 3.It is not advisable to mount the transmitter onto metal surfaces as it
• will diminish or block RF signals between the transmitter and the
• receiver. However, if this is the only option then we recommend that

WC180-SS you use the double sided tape provided for mounting the push button. WIRELESS DOORBELL KIT 4.Operating range will decrease if battery in transmitter is in low power status.

• User Manual
• 5.It is not advisable to mount the transmitter in the outdoor directly
• without any shelter which could accelerate aging of plastic materials.
• Please carefully read this user manual before using and installation

TroubleshootingTroubleshooting

• Info & Contact Information
• This product is warranted for 1 year by Safeguard Supply. Please
• 1.The receiver doesn’t sound
• consult the Safeguard Supply website at safeguardsupply.com/

Ÿ Check the doorbell button battery, replace it if necessary. warranty-policy for additional information. Ÿ The receiver is not securely set into the outlet . To contact us: Ÿ The receiver could be out of range of the doorbell button. Ÿ The receiver may not have paired with the doorbell button. Safeguard Supply Ÿ Ensure the volume is not muted (press volume button).

• info@safeguardsupply.com
• 800-366-7235 2.Operating range is reduced For warranty information, visit: https://safeguardsupply.com/ Ÿ Metal structures can reduce the range of the product. Avoid warranty-policy mounting the push or chime on or near metal structures. For

, visit: https://safeguardsupply.com/fcc Ÿ Other equipment can cause radio interference that affects your doorbell. Ÿ Walls and ceilings will reduce the range. Ÿ Weak batteries will reduce range. Replace every 12–18 months. 6 3.Pairing a transmitter to the receiver: Quick Start (1) Select the ringtone you want to associate with the transmitter.

• Music Change Select ringtone
• (2)Hold and press the Volume Control
• button for 5s until a “Ding-Dong” sound

1. Volume Control Button Location: Press the Volume Control is heard and the LED strobe starts button on the receiver. Press the button to toggle between High and flashing.

The receiver is now in paring Low volume and mute. mode. *The volume level setting does not affect the strobe light.

• Hold Volume Change for 5s
• 2. Set Ringtone Using the Music Change Button: Press the
• Music Change button to choose your favorite ringtone. Stop
• pressing the button once you hear the ringtone you want to use.
• (3) Push the center push on the push
• button (or other transmitter) to send a
• signal to the receiver.
• Press the button