XP60 User Manual

Light Control XP60 Congratulations on a wise purchase!

• Light Control

Your light control is activated by changes in surrounding light. For optimum performance, the light control should be positioned in an area exposed to a strong source of natural light. Ideal positioning is in a lamp fixture located within 4 ft. of a window or other light source.

Once power is supplied to your light control, the control will turn on at dusk (or when the surrounding light level becomes low enough) and then turn off at dawn (or when the light-level is bright enough). Once the bulb automatically turns off, it will remain off until the following night. As long as power is supplied to the control, the light control will continue to cycle on and off.

Caution: For a 3-way lamp, the lamp must be set to the medium setting before installing the XP60.

1. Turn "OFF" power to light fixture.
2. Screw light control into light fixture.
3. Screw bulb into light control.
4. Position control so that the photocell eye faces a strong source of light. The ratcheting screw shell design allows you to rotate the control in a complete circle (turning clockwise).
5. Turn "ON" power to light fixture (middle setting only for 3-way lamp).

• 60W Max Bulb UP
• 25W Max Bulb DOWN
• Light Sensor
• Ratcheting Screw Shell
• Lamp Socket

During the day, covering the light sensor with your finger should turn the light on. When you remove your finger, the light should go off.

For indoor or outdoor use. Outdoor use must be in a protected fixture to prevent direct exposure to rain. Do not exceed 25 watts when using in an enclosed fixture.

Problem: Control turns on at dusk during the first night of operation but does not turn on at dusk during the second night (or second timing cycle) of operation. This means the light control did not see enough light during the daylight hours to reset. This problem usually occurs on cloudy or overcast days when there is no sunlight. Solution: Move light control closer to a natural light source or rotate the Photocell on the light control toward the light (see step 4).

Problem: Light control does not turn on at all. Solution: Make sure power is supplied to light fixture. Ensure light bulb is not burned out. For 3-way lamp fixtures, make sure the lamp switch is set at the middle switch position. The light control should turn on after the photocell eye sees darkness or after the photocell eye is completely covered.

• 120 V AC
• 60 watts max.
• Incandescent bulbs only

The product you have purchased is guaranteed against defects in workmanship and materials for the period stated on the package. Warranties implied by law are subject to the same time period limitation. Some states do not allow limitations on how long an implied warranty lasts, so this time limitation may not apply to you.

If the product fails due to a manufacturing defect during normal use, return the product and dated sales receipt to the store where purchased for replacement OR send the product and the dated sales receipt to: Lamson & Sessions 25701 Science Park Drive Cleveland, OH 44122 USA Attn: LHP Customer Service

Not Covered - Batteries, light bulbs, and other expendable items are not covered by this warranty. Repair service, adjustment and calibration due to misuse, abuse or negligence are not covered by this warranty. Unauthorized service or modification of the product or of any furnished components will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, set-up time, loss of use, postage, unauthorized service, or other products used in conjunction with, but are not supplied by, Lamson & Sessions.

All requests for replacement must include a dated sales receipt (copies accepted). LAMSON & SESSIONS IS NOT LIABLE FOR LOST PROFITS, INDIRECT, SPECIAL, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE PRODUCT. As some states do not allow the exclusion or limitation of incidental or consequential damages, the above limitation and exclusion may not apply to you. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry Canada.

• Extend-A-Chime® – lets you hear your existing wired doorbell in remote areas of your home or yard
• Plug-in and Battery Doorbells and Chimes
• On/Off Remote Switches
• Touch and Automatic Lighting Controls

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If you have questions or need further assistance, please call Lamson & Sessions at: 1-800-346-2646 Mon. - Fri., 9 a.m. - 4 p.m. EST.

Carlon® 25701 Science Park Drive Cleveland, OH 44122 www.lamson-home.com

Made in China 0408 IS171